SAVE
(ALT) BACKPAGE
PRESET
03
PRESET
04
EFFECT
(ALT) MOD SOURCE
MOTION/SPEED
PRESET
02
PRESET
01
ON/OFF
ENVELOPE
CALIBRATE
LFO/SEQ
INVERT/SEQ ENABLE
DEPTH
(ALT) FREQUENCY/DELAY
HOT HAND
MOTION CONTROLLED PHASER/ FLANGER
ON/OFF
SELECT
(HOLD FOR ALT MODE)
02
04
06
07
03
02
04
06
07
01
05
02
03
05
00
08
07
06
01
02
03
05
04
00 08
07
06
01
03
05
01
FLANGER
PHASER
FLAIL
/SLOWPICK/FAST
STRUM
Pedals
ON/OFF (left) Pedal
Pressing this pedal once engages the effect that is selected. Pressing the
pedal again will turn the effect off and the bypass on. There is an
ON/OFF LED
right above the pedal that notifies you when the effect is turned on.
Technical Note: In bypass mode, the signal still passes through a unity-gain, high input impedance,
low noise buffer.
SELECT (right) Pedal
The SELECT pedal cycles through the 4 presets in a repeating pattern. The 4
LEDs above this pedal indicate which preset has been selected.
The preset will change when the pedal is released. If the
SELECT pedal is
held down, it invokes
ALT MODE, which changes the function of the DEPTH and
EFFECT knobs to FREQUENCY/DELAY and MOD SOURCE. ALT MODE also changes
the SAVE button into a switch to enter the Back Page parameter editor. When
the SELECT pedal is held down long enough to go into ALT MODE, the preset
selection will not advance upon pedal release.
ON/OFF pedal Select pedal
Saving Presets | 2322 | Pedals
Saving Presets
The PRESET feature of this product has been designed to be simple. This
product allows you to save
4 different configurations so that they may be eas-
ily recalled from the standing position. When you receive your product from
the factory, we have selected what we think are 4 useful configurations. You
may either keep these or replace any of them with your own settings. Should
you wish to return to the original factory presets, see the Restore Defaults
section on page 33.
01 : Select and edit a preset
By stepping on the SELECT pedal you can select one of four user presets.
Edit a preset by changing values for
DEPTH, FREQUENCY/DELAY, EFFECT, MOD
SOURCE, MOTION/SPEED or INVERT. Any time that you change the knob posi-
tions of a given preset, that preset
LED will blink slowly to indicate that the
preset has been edited.
02 : Press and hold the SAVE button for two seconds
The preset LED will blink rapidly to signal that the saving process has begun.
When the light becomes solid, the save process is complete. Note that this
process will over-write any setting that was previously stored in this location.
ADVANCED USER NOTE
It is possible to save different calibration settings for each preset. The procedure is described in the
CALIBRATE section on page 12. Different settings of the Back Page parameters may also be saved
for each preset. See page
24.
SAVE
(ALT) BACKPAGE
PRESET
03
PRESET
04
EFFECT
(ALT) MOD SOURCE
MOTION/SPEED
PRESET
02
PRESET
01
ON/OFF
ENVELOPE
CALIBRATE
LFO/SEQ
INVERT/SEQ ENABLE
DEPTH
(ALT) FREQUENCY/DELAY
HOT HAND
MOTION CONTROLLED PHASER/ FLANGER
ON/OFF
SELECT
(HOLD FOR ALT MODE)
02
04
06
07
03
02
04
06
07
01
05
02
03
05
00
08
07
06
01
02
03
05
04
00 08
07
06
01
03
05
01
FLANGER
PHASER
FLAIL
/SLOWPICK/FAST
STRUM
01 02
(13 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals