Source-audio Soundblox Pro Multiwave Bass Distortion Pro User Manual download pdf (Page 9)

Morphing | 1716 | Preset Saving

MORPHING

The expression input on the MWB Pro can be used to morph between

two presets. More specically, you can morph from between banks from

preset

1 to 4, 2 to 5, and 3 to 6. For example, let’s say preset 1 is saved as

a Multiband normal setting and preset

4 is a Multiband octave setting.

By connecting a passive expression pedal, you can fade from the preset

Multiband normal sound into the octave effect by rocking the expression

pedal from heel to toe. As you fade between the sounds, the color of the

LED above the footswitch will fade from green (bank A) to red (bank B) to

indicate where the morph is between the two presets.

In contrast to the

MIX control, the morphing is not a cross fade between

two sounds but rather a gradual shift between all of the individual

parameters. So the middle of expression pedal range is truly an “in-

between” sound.

There are

276 possible pair combinations of sounds and some will sound

better than others. Some obvious applications are morphing from clean

to distorted sounds, low drive settings to high drive settings, changes in

volume, or between dramatically different sounds.

The expression pedal can be effectively inverted by pressing the

PRESET

BANK

button. This will toggle start and stop presets for the pedal. Keep

in mind that adjusting knobs while using the expression pedal will only

control the preset in the currently selected bank, independent of the

expression pedal position. Also, while tweaking presets to get the desired

pair of sounds for morphing, don’t forget to save before switching banks

with the bank select button.

The expression pedal can also be used as a means of effectively switch-

ing between preset banks, allowing access to all

6 presets with foot

controls only.

The expression input is intended for use primarily with a passive expres-

sion pedal. It could potentially be used with a Control Voltage

(CV) output

but the input voltage range is limited to

0 to 3.3V. Take extra precaution

before connecting any

CV output to the MWB Pro. Exceeding the voltage

range (above

3.3V or below 0V) could damage the unit.

PRESET SAVING

An edited preset can be saved by pressing and holding a footswitch as

described in the Controls: Footswitches section. An edited preset can be

saved to any one of the

6 preset locations. For example if preset 1 has

been selected and edited, it can be saved to preset location

3 by pressing

and holding the

3/6 footswitch. Once the preset has been saved to that

location, the new location will be the selected preset. The unedited preset

will still be at location 1.

Presets can be copied across preset banks by holding the

PRESET BANK

button and then pressing and holding a footswitch. For example, if preset

2 has been selected and edited, holding the PRESET BANK button (A) and

then pressing and holding footswitch

2/5 (B) will save the current settings

to location

5. It could also be saved to locations 4 and 6 in the same man-

ner. Once the preset is saved to another bank, the preset in the current

bank will stay selected and

NOT be saved to its own location since it was

saved elsewhere as a new preset.

Saving between banks is especially useful when setting up parameters

for morphing between preset banks.

EQ AMOUNT CLEAN MIX

MULTI BAND

SINGLE BAND

FULL0

OCTAVE

NORMAL

FOLDBACK

OCTAVE

NORMAL

FOLDBACK

DRIVE DISTORTION MIX

HH ENABLE

CALIBRATEPRESET BANK

4-6

62 125 250 500 1K 2K 4K

+12

-12

1-3

< >

+12

-12

(NG) (HG) (HS) (HA) (HR)

MULTIWAVE BASS DISTORTION

CLEAN BOOST / EQ

BACKPAGE

MODE

- Continued

1 2 3 4 5 6 7 8 9 10 11 12 13

Comments to this Manuals

No comments

Source-audio Soundblox Pro Multiwave Bass Distortion Pro User Manual Page 9

Comments to this Manuals

Related products and manuals for Audio Source-audio Soundblox Pro Multiwave Bass Distortion Pro